#Plasmacam user manual manuals#

Alcatel Lucent 4020 User Manual.pdf Plasmacam dhc2 manual - free ebooks download Plasmacam dhc2 manual download on free books and manuals search. Video Manual The PlasmaCAM system includes a video-based instruction manual that helps you with additional. в†і Laser Pointers, Pen Markers, Remote Controls, Drawing Tablets, etc.PlasmaCAM DHC 2 в„ў CNC Plasma Profiling System.в†і Fab Tables, Grind Stations, Material Storage & Handling.в†і Water Tables, Ventilation, Air Handling.в†і Sharpe 3 Stage Air Filter & Drying System.в†і Air Dryers, Air Filters, Air Compressors, Etc.в†і Metal Bending, Rolling, Notching, Drilling, Saw Cutting.в†і Mig Welders, Tig Welders, Spot Welders.в†і EasyScriber Drag Style Scriber for Hypertherm.в†і Roark Supply-Your Online Source for Abrasives.в†і Steel F/X Your Metal Patina & Dye Connection.в†і DIY Plasma Table & Accessory Discussion Forum.в†і Thermal Dynamics / Esab Plasma Cutters.в†і Pricing, Advertising, & Marketing Your Products Forum.в†і Hypertherm's Tips to Troubleshoot Cut Angularity.в†і Hypertherm's 10 Common Plasma Cutting Mistakes.в†і Hypertherm's Basic Tips to Improve Cut Quality.в†і CNC Plasma Cutter Project Picture Gallery.в†і DXF Art - DXF Clip Art File Sharing Forum.DXF DESIGN & PROJECT PICTURE SHARING FORUMS.WELCOME CENTER, GOOD INFO & MEET OUR SPONSORS.In this case, I should probably refer to him as OP#2. The original post was about 5 months ago and you are correct - no mention of hand torch. I measured the resistance of the power board resistors on an old 45 XP power board. I don't think the original poster mentioned anything about a hand torch.

In the OP's case, he is using a hand torch, so the CPC port is not applicable. Do not try to make your own cord or alter ours by cutting it apart, or you will likely endanger yourself and damage your controller! Warning: cord includes special low-EMI cabling and internal resistors. Carefully follow testing instructions in manual prior to use. Buy an additional cord for an additional cutter, if you lost the original jumper, or replace if damaged or burned out (no longer reports arc voltage or triggers cutting). Kit includes cord, test/manual cutting jumper, strain relief, and various connectors for wiring to most any cutter.

#Plasmacam user manual install#

Install a torch control cord in a plasma cutter you want to use with the machine. You can phone Plasmacam tech support for a copy of this form. If you have not already done so, you will want to file the change of ownership form for you table with Plasmacam so you can become registered and purchase replacement parts as well as join the Plasmacam Owner's Community Online Forum.

#Plasmacam user manual plus#

A replacement Video Manual is available from Plasmacam for $10 plus shipping. This involved removing the cover from your 45xp and cutting/splicing the torch trigger wire as well as connecting the red and black wires which monitor the raw arc voltage used for the torch height control. You will need to follow the installation instructions as described in Chapter 4 of the Video Manual. The torch control cable included with this kit contains the proper voltage divider as part of the cable.

What you will need to do is buy and install the Plasmacam torch control wiring kit as described below. So you will not need to change the voltage divider, because it is not used for the hand torch. The CPC port with voltage divider is only for machine torch, not the hand torch. If I am using the hand torch do I still need to change the voltage divider from 50:1 to 21:1:1 or do I leave it at the factory 50:1 for hand torch use? The Hypertherm user manual advises under the machine torch section to change the factory 5-position voltage divider from the factory setting of 50:1 to the plasmacam setting of 21:1:1. I am using the hand torch not a machine torch. I just purchased the 5x10 plasmacam table and attempting to install a hypertherm xp 45 to the table.